Integrate Cisco Umbrella with Cisco SecureX

-

In this article we're going to take a look at how to integrate Cisco Umbrella with the Cisco SecureX dashboard.


The process is rather straight-forward in that the administrator only needs to enable single sign-on within Umbrella in order for this to work.

To enable single sign-on within Umbrella, complete the following steps:

Login into Cisco Umbrella and navigate to Admin > Authentication



Enable single sign-on and select 'Cisco Secure Sign-On' and click 'NEXT'



Verify the Cisco Secure Sign-On by testing the configuration. If unsuccessful, follow the on-screen instructions.

When successful, the pop-up page with appear to let you know that SAML is configured correctly and you should also see a small green tick on the Umbrella page (as shown in the screenshots below).





For step 3 you will need to Save and Notify users that SAML has been configured. Read the on-screen information and if happy to proceed, mark the two check boxes and click 'SAVE AND NOTIFY USERS' to complete the single sign-on for Cisco Umbrella.


Single sign-on for Cisco Umbrella is now complete and you should now be able to verify this under Admin > Authentication (as shown in the screenshot below).







Kelvin Charles - Network and Cyber Security Professional.

Popular Posts

Capturing EAPOL and RADIUS Using Wireshark

-
Image
In this article we are going to take a look at how to capture Extensible Authentication Protocol Over LAN (EAPOL) and Remote Authentication Dial-In User Service (RADIUS) packets using Wireshark. This article can be useful for troubleshooting 802.1x within your environment and can also be used for learning purposes. The following topology has been used to gather the required output for this article. Note: This article will only cover the switch configurations that are required to gather EAPOL and RADIUS configuration. Overview of the Topology The supplicant is configured to perform 802.1x using EAP-TLS as the authentication method The user certificate on the supplicant will be used for authentication The supplicant has Wireshark installed Cisco ISE is used for authentication and authorisation The supplicant is assigned to VLAN 10 upon authentication and all other endpoint ports are assigned to VLAN 99 Sniffer device is running Wireshark in order to capture RADIUS flows via SPAN 802.1x ...
Read more

Configuring Cisco ISE for SNMPv3

-
Image
In this article I would like to cover how to configure SNMPv3 for Cisco Identity Services Engine (ISE). In a few deployments I’ve done, I’ve come across the need to configure ISE to send SNMPv3 traps to a Network Management System (NMS). SNMPv3 is perfect for ensuring the authentication and encryption of SNMP traffic, something that can’t be done with inferior SNMP versions. Now, one would assume that we could just go ahead and configure ISE for SNMP via the GUI however, unfortunately that’s not the case. To actually configure ISE to send traps to an NMS system we need to configure the settings via the CLI. The demonstration in the article is performed using a standalone ISE. This demonstration also assumes that you have connectivity between your NMS platform and ISE. To see a live demonstration with testing, refer to the video that accompanies this article. Configuration Steps Enable SNMP So that we can configure the required SNMPv3 settings for ISE, SNMP needs to be enabled. iselab/a...
Read more

Configuring Cisco Smart License Software

-
In this article, I would like to demonstrate how to configure Cisco Smart Licensing on the virtual Cisco Adaptive Security Appliance (ASAv). This post assumes that readers already have access to there own Smart Account and would like to know the process of applying licenses. Step 1: Generate ID Token Sign into your Cisco Software Portal: software.cisco.com and navigate to “Smart Software Licensing” You will now need to create an ID token for your device, this is required for communication between the device and the licensing authority. Follow the steps below to create a new token. Click Inventory >>> General >>> New Token and select your preferred options and enter a description for your token. Once you are happy with your token settings click Create Token . You should now have a token created which can be copied over to the device you wish to license. All commands and output from this point will be related to the ASA so please seek out further advice if you w...
Read more

Demystifying IBNS 2.0 Configuration

-
Image
In this article I would like to go through a typical Identity Based Networking Services (IBNS 2.0) configuration, breaking down each so that we can better understand the configuration. While there are many configuration elements of secure network access, this article will focus on the Cisco Common Classification Policy Language (C3PL) configurations. I must admit, when I first got a glance of some IBNS 2.0 configuration, I was a little taken back at the amount of configuration. However, after reading up about it, and refreshing parts of my CCNP R&S skills, I was able to understand how IBNS 2.0 configuration comes together. This article will NOT focus on use cases for using IBNS 2.0, however, I would like to point out some good, online documentation that will provide you with some useful information. IBNS 2.0 at a glance Identity Based Networking Command Reference Guide Cisco Live IBNS 2.0 Lab Guide Configuring Identity Service Templates Configuring IEEE 802.1x Port-Based Authent...
Read more

Kali Linux :: CAM Table Overflow Attack Demonstration

-
Image
As part of my on-going studying for the CCNA Security 210 – 260 certification I have been exploring different types of network attacks, one of which is CAM table overflow attacks. In this article I would like to share what I have learnt and provide a demonstration of the attack carried out in a lab environment. To understand my demonstration, you first need to understand how a CAM table overflow attack works and what happens as a result of the attack.   Switches build Content Addressable Memory (CAM) tables based on mac-addresses and port numbers. When a switch receives a frame it checks the table to see if the source mac-address is already known, if the source mac-address is unknown the switch will add the mac-address to the table along with the port number. The switch then checks the destination layer two frame and if no entry exists the switch broadcasts the frame out of all ports except the port in which the frame was received. Presuming the destination mac-address wants to res...
Read more