Integrate ISE with Cisco Prime

-

In this demonstration I will show you how to add Cisco ISE to Cisco Prime.


The following equipment has been used in this demonstration:
  • Cisco Prime 3.5
  • Cisco ISE 2.6 (Standalone)

Navigate to Administration > Servers > ISE Servers



On the right-hand side of the screen, click on 'Select a command' and select option 'Add ISE Server' followed by 'Go'.


Enter the required settings for your Policy Admin Node (PAN) and click 'Save' once done.



Once complete, return to 'ISE Servers' where you should see the ISE server that you've added.







Kelvin Charles - Network and Cyber Security Professional.

Popular Posts

Demystifying IBNS 2.0 Configuration

-
Image
In this article I would like to go through a typical Identity Based Networking Services (IBNS 2.0) configuration, breaking down each so that we can better understand the configuration. While there are many configuration elements of secure network access, this article will focus on the Cisco Common Classification Policy Language (C3PL) configurations. I must admit, when I first got a glance of some IBNS 2.0 configuration, I was a little taken back at the amount of configuration. However, after reading up about it, and refreshing parts of my CCNP R&S skills, I was able to understand how IBNS 2.0 configuration comes together. This article will NOT focus on use cases for using IBNS 2.0, however, I would like to point out some good, online documentation that will provide you with some useful information. IBNS 2.0 at a glance Identity Based Networking Command Reference Guide Cisco Live IBNS 2.0 Lab Guide Configuring Identity Service Templates Configuring IEEE 802.1x Port-Based Authent...
Read more

Display Cisco ISE Usernames for Failed Authentications

-
Image
In this quick tip Cisco ISE article I would like to point out how ISE administrators can displays usernames for failed authentications. The following has been tested on ISE 2.4 but is relevant for older ISE versions. When a user/machine fails authentication ISE will mask the identity automatically. This can be seen in the RADIUS Live Logs and looks like the screenshot (1) shown below. Although you can click on the details of each live log, sometimes it’s good to know what the identity is to troubleshoot further. The good news is that with ISE, we can unmask the identity, however, the bad news for some is that you can only keep identities unmasked for a limited time, depending on ISE version. As of up to ISE 2.4 patch 3 you cannot keep identities unmasked permanently, in fact, the maximum time in which you can keep identities unmasked for is 30 minutes before ISE masks them again. As mentioned, this is not convenient and was in fact raised as a bug (CSCvh91118). I believe ISE releases ...
Read more

Why Snapshots Could Break Your Virtual ISE Deployment

-
In this article I would like to focus on virtual machines, in particular Cisco ISE virtual machines running on VMware. I will explain why virtual ISE deployments DO NOT support snapshots as well as the potential issues that you could face if snapshots are enabled. So what is a snapshot? A snapshot is a copy of a virtual machines disk file (.VMDK) at a particular point in time. VMware allows you to take manual snapshots of a virtual machine or even automatically take snapshots of devices at a specific time. Snapshots are useful in situations where an operational device is rendered useless for whatever reason and you would like to restore that device back to a working state. So why doesn't Cisco ISE support snapshots? Cisco ISE comes with its own backup and restore utilities and not only that, Cisco ISE doesn't support backups because the data within the nodes is constantly changing and is being synchronised with the database. What happens if snapshots are taken of ISE nodes? If...
Read more

Configuring Cisco ISE for SNMPv3

-
Image
In this article I would like to cover how to configure SNMPv3 for Cisco Identity Services Engine (ISE). In a few deployments I’ve done, I’ve come across the need to configure ISE to send SNMPv3 traps to a Network Management System (NMS). SNMPv3 is perfect for ensuring the authentication and encryption of SNMP traffic, something that can’t be done with inferior SNMP versions. Now, one would assume that we could just go ahead and configure ISE for SNMP via the GUI however, unfortunately that’s not the case. To actually configure ISE to send traps to an NMS system we need to configure the settings via the CLI. The demonstration in the article is performed using a standalone ISE. This demonstration also assumes that you have connectivity between your NMS platform and ISE. To see a live demonstration with testing, refer to the video that accompanies this article. Configuration Steps Enable SNMP So that we can configure the required SNMPv3 settings for ISE, SNMP needs to be enabled. iselab/a...
Read more

Configure the Cisco ASAv To Use Virtual Serial Ports

-
Image
In this article, I will demonstrate how to configure the ASAv so that you use a virtual serial port. This article assumes that you have installed the virtual Cisco Adaptive Security Appliance using VMware workstation or it’s equivalent and that you can only access the ASAv CLI via the VMware client. By default, the virtual serial console on the ASAv is disabled, so that it can be enabled, a few commands are required. Use Case At present, I only have access to the ASAv CLI using VMware Fusion but I want to use my computers terminal software to access the CLI for use with GNS3. The following steps assume you have already installed the ASAv Steps Power on the ASAv and access the CLI via VMware workstation or it’s equivalent Enter the following commands on the ASAv Enable Configure terminal cd coredumpinfo Copy coredump.cfg disk0:/use_ttyS0 – This will enable the serial console once saved to Disk0:/ Now shutdown the ASAv and upon reloading the ASAv will now send its output to the s...
Read more